BRP Evinrude Spécifications Page 19
- Page / 102
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
17
BOAT RIGGING
BATTERY INSTALLATION
1
Battery Switch Operation
• Select the primary battery for normal operation.
• Secondary batteries should only be selected for
emergency starting.
• ALL or BOTH switch position is for emergency
starting only.
Provide operator with the documentation sup-
plied by the battery switch manufacturer. Make
sure that the operator is informed of proper
battery switch operation.
The negative (–) terminals of a mul-
tiple 12-volt battery installation must be con-
nected together.
Auxiliary Battery Charging
EVINRUDE E-TEC V4 – V6 MODELS
Evinrude E-TEC V4–V6 outboards are equipped
with isolated battery charging capability. The iso-
lated charge connection must only be used to
charge a single 12-volt battery or two 12-volt bat-
teries wired in parallel.
Never connect an external battery
isolator to the stator of an Evinrude E-TEC.
Accessory Charge Lead Kit, P/N 5006253, is
routed from a connector on the outboard’s electri-
cal harness to the accessory battery.
The accessory charging kit must
never be connected to any battery of a 24-volt
electrical system.
EVINRUDE E-TEC 40 – 90HP MODELS
Evinrude E-TEC 40 – 90 HP outboards do not
have a built in isolator feature. Proper methods
must be used to connect a second battery.
Battery charging output on 40 – 90 HP models is
25 Amps. Be sure to follow published standards
for wire gauge selection. Refer to Battery Cable
Requirements on p. 16.
If a battery isolator is desired, a battery switch,
such as P/N 506161, and a voltage sensitive
relay, such as BEP model 710-125A, can be used
to create a battery isolator/combiner.
The voltage sensitive relay (VSR) regulates
charging of a second battery based on predeter-
mined voltage levels of the primary battery.
Never connect an external battery
isolator to the stator of an Evinrude E-TEC.
90° V6 Models
1. Accessory battery charge connector
004125
NOTICE
NOTICE
1
60° V4–V6 Models
1. Accessory battery charge connector
004944
1
NOTICE
NOTICE
- BRP US Inc 3
- Technical Publications 3
- 250 Sea Horse Drive 3
- TABLE OF CONTENTS 4
- SAFETY INFORMATION 6
- EMISSION-RELATED 9
- INSTRUCTIONS 9
- BOAT RIGGING 10
- Control Installation 11
- Control Cable Routing 12
- INFORMATION DISPLAY 13
- INFORMATION DISPLAY SYSTEMS 14
- BATTERY INSTALLATION 17
- Battery Cable Requirements 18
- Batteries 18
- Auxiliary Battery Charging 19
- FUEL SYSTEM 22
- REQUIREMENTS 22
- Fuel System Primer 23
- Fuel Filters 23
- Fuel Flow Requirements 24
- REMOTE OIL TANK 25
- INSTALLATION (V4 – V6) 25
- ALLON (11.4 L) TANK 26
- ALLON TANK 26
- Oil Tank Profiles 27
- CABLE AND HOSE 28
- INSTALLATION 28
- Protective Sleeve/Conduit 29
- Battery Cables 29
- Fuel Hose 29
- Oil Supply Hose 29
- Oetiker Clamp Servicing 30
- OUTBOARD INSTALLATION 33
- Transom Brackets and Jack 34
- Mounting Hardware 34
- TRANSOM MEASURING 35
- AND DRILLING 35
- Transom Height 36
- Transom Drilling Locations 36
- ANUAL TILT MODELS 37
- OWER TILT MODELS 37
- This is not a template 38
- 25–30 HP, MANUAL TILT MODELS 42
- 7.39 in 44
- (187.6 mm) 44
- 2.1 in 44
- (53.1 mm) 44
- 10.25 in. (260.4 mm) 44
- 9.38 in 45
- (238.25 mm) 45
- LIFTING THE 46
- OUTBOARD 46
- STEERING SYSTEMS 48
- Manual Hydraulic Steering 49
- Drag Links 49
- OUTBOARD MOUNTING 50
- OUTBOARD RIGGING 53
- EVINRUDE E-TEC 90° V 54
- MODELS 200–300 HP 54
- Control Cable Installation 55
- Battery Cable Connections 56
- SystemCheck Harness 56
- Connections 56
- I-Command Network Connections 57
- ICON Network Connections 58
- Water Pressure Gauge 59
- EVINRUDE E-TEC 60° V 60
- MODELS 115–200 HP 60
- EVINRUDE E-TEC 67
- MODELS 40–90 HP 67
- YLINDER MODELS 71
- LL MODELS 71
- MODELS 15–30 HP 73
- FUEL AND OIL PRIMING 77
- FUEL SYSTEM PRIMING 78
- OIL REQUIREMENTS 79
- Break-In Oiling 80
- OIL SUPPLY PRIMING 81
- 115 – 200 HP 60° V4/V6 and 82
- 200 – 250 HP 90° V6 Models 82
- 15 – 90 HP Models 84
- PREDELIVERY 85
- RUNNING CHECKS 86
- PROPELLERS 88
- WATER TEST AND FINAL 90
- ADJUSTMENTS 90
- Water Pressure Chart 91
- Tilt Limit Switch Adjustment 92
- (75 – 300 HP) 92
- Trim Sending Unit Adjustment 93
- (25 – 60 HP) 94
- Trim Tab Adjustment 95
- Dual-Outboard Alignment 96
- SAMPLE PREDELIVERY CHECKLIST 99
Produits connexes et manuels pour Moteur BRP Evinrude
Moteur BRP Evinrude E-TEC Spécifications
(62 pages)
(62 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels